Industrial Light Fixture

October 24, 2016 6 Comments

As soon as we moved into the house we remove those oversized fans. They just made our dining and living rooms looking even smaller and congested.

The question of what would be in place of the fan that we removed remained open, and we decided not to worry about it before the major renovations were done.
The idea of this light fixture came along spontaneously. As we were putting together our dining room, we would make regular visits to the local Home Depot. During one of our regular runs to the store, Dmitri called me to come over to the isle he was hanging around.
When I came, I saw plumbing pipe pieces laying on the floor representing I-have-no-idea-what. Then he explained it that the figure represented the light fixture he got an idea for.

I was skeptical about it as it didn’t look impressive at all.
When we got home Dmitri did a sketch of his idea as I liked it. Especially for its industrial flair that would match our beams.

It is very quick, fun, easy, and budget-friendly (we spent ~$180 on parts) light fixture that will make a bold statement.

There are really lots of ways to connect all fittings and feed the wires. You can make yours of any shape, size, and color you like. The wires are coming in many different fun colors. You can absolutely improvise. However, if you like this exact light fixture you can follow this step-by-step instructions.

Please note, Dmitri has some experience with electricity, so he did all the wiring by himself. However, if you are not comfortable with that, find someone who can do it for you or at least consult you.

Parts we used:

  1. Black steel piping and fittings
    a.  1 ½” floor flange – 1pc
    b.  1 ½” x 1 ¼” bushing -1 pc
    c.  1 ¼” x 1” bushing – 1pc
    d.  1” x 1” union – 1pc
    e.  1” x 1” x ¾” tee – 3pc
    f.   1” x 1” x 1” tee – 2pc
    g.  1” x 4” nipple –  9pc (you will see 8 at the picture…  It is just because we miscounted         it in the store)
    h.  ¾” x 3” nipple – 3pc
    i.  1” elbow         – 3pc
    j.  ¾” elbow        – 3pc

2. Hardware
a.  ½” x 6” lag screws

3.  Electrical Supplies
a.  2-CONDUCTOR 18-GAUGE RED COTTON TWISTED WIRE   – 30’
b.  Lamp socket black – 6pc
c.   Incandescent bulb – 6pc

1.    Prepare

The new black iron piping pieces are coming coated with machine oil. So before assembling them into the light fixture we cleaned them using regular dish soap and warm water. Then we let them air dry. You can also use paper towel or dry rag to dry them.

When we assembled our light fixture we did not have this blog in mind, so we weren’t taking thorough step-by-step pictures. For the purpose of this post we will replicate this light fixture with exact the same piping, however, instead of wires we will use just plain thin ropes.

Pre-cut the wires to desired length before feeding them through the pipes. For our size light fixture we pre-cut the wires to 5’ each. The length will depend on the lamp size and your preferences. Make sure you leave enough whip on a wire for electrical connection on both ends (ceiling box and bulb socket).

If you want to double check if you have all part, you can lay out the part on the working surface

2.    Assemble

Get a 1” tee, that will be in the middle of the fixture and feed all wires through in both direction leaving enough slack for other parts.

Then assemble the top part of the fixture where it will connect to a ceiling. Screw together flange, bushings (reducers), nipples and join fittings.

Now, get top wires in one bunch and, with slightly twisting them together, feed them through the connected fittings. All iron fittings have sharp threaded ends. Be careful not to damage cotton covered wires insulation, as parts of the wiring will be exposed. You want them to be nice and neat.

Next, continue with connecting parts one by one as you pull wires through them.

You are now ready to make electrical connections to lamp sockets. When wiring sockets remember to connect hot wire to the socket base. The threaded socket is the neutral. The lamp will usually work either way, but safety comes first.

3. Install

WARNING:  If you are not familiar with basic electrical circuits, please find someone who can do it for you safely.

The light fixture is ready for ceiling installation. First, twist all hot wires into one wire nut and connect a pigtail for easy connection. Do the same with neutral wire. We installed our fixture in the place of the old ceiling fan. The support for electrical box was sufficient to hold the piping lamp, the weight was same. As far as electrical connection, if you are not familiar with basic electrical circuits, please ask a professional to complete this step for you. Otherwise, proceed with connecting hot (usually black) and neutral wires with pigtails from your lamp. Using lag screws secure lamp base (flange) to the ceiling box. And you are done!

October 1, 2016
November 5, 2016

6 Comments

  1. Julia

    January 22, 2017

    This looks really amazing. Thanks for sharing this ideas. I am so much into these kinds of lamps at the moment.
    Cheers, Julia

    • Nadia Karpov

      January 26, 2017

      Julia, thank you! I can’t wait to see your creation on your blog. Even though it is all in Deutsch, I will still enjoy some of your pictures! 🙂

  2. Julie Christiansen

    March 17, 2017

    So creative! What a beautifully crafted industrial light. Thanks for sharing at My Busy Beehives #beeparty!

    • Nadia Karpov

      March 19, 2017

      Thank you, Julie! thank you for visiting!

  3. Tarahlynn

    March 21, 2017

    This looks awesome! Thanks for sharing with us at the To Grandma’s house we go Wednesday link party! You will be featured tomorrow morning when the next party starts!

    • Nadia Karpov

      April 5, 2017

      Thank you Tarah!

Comments are closed.

RELATED POSTS